Swingmaster Sw Swinger. Electra Swinger. KDB Revolver. Besam Automatic Door Parts Established in , Besam entered the industry focusing on the healthcare market. In the 70's and 80's they expanded to sliding and revolving doors also. Taking the industry by storm as the less expensive option Besam can be found virtually everywhere.
Our wide selection of Besam automatic door parts range from the very oldest to the newest models. Those small hard to find parts are all right here. Whether you're in need of a motor gearbox or just a header screw, we have it.
The open position is held by the motor. When the hold open time has elapsed, the operator will close the door automatically, using spring force and motor. The door will slow to low speed at latch check before it reaches the fully closed position. The door is kept closed by spring power or extended closing force by the motor. During power failure the operator acts as a door closer with controlled closing speed. If necessary, the spring tension can be electronically adjusted with a potentiometer to required closing force.
When an OPD sensor is mounted on the frame or operator header just above the swing side of the door, it will—when activated—either keep the door open or closed. The sensor is not active during opening and closing. Lock-out signal must be connected for proper function. Potentiometer for opening delay is to be set to max. As soon as unlock signal is received the door will start to open.
The output signal shall be active low. The impulse will open the door and the door will stay open until a new impulse is given. If no impulse is given the door will close after 15 minutes. This can be made infinite by changing group of parameters see page The presence impulse is active during fully open and closing.
The sensor is mounted to the approach side of the door. Once the door is closed, the sensor is ignored and will not be active until the next impulse is received. Note: When installed as a pair of doors, the presence impulse signal will re-open both doors.
When a sensor that is mounted on the swing side of a door detects an object, it will send a command to the control unit to stall the door. If the control unit has received a short signal from the sensor and there is still hold open time left on the control unit, the door will continue on its way open if the object has cleared. Presence detection has a higher priority than presence impulse. Note: When installed as a pair of doors the presence detection signal will stop both doors, except for double egress doors.
The behavior for double egress doors can be changed see page The sensor is not active in program mode OFF, manually opened door or during battery operation. Both presence impulse and presence detection can be monitored.
If a sensor becomes defective, the operator will not accept any impulses and will then work as a manual door closer. A relay output is used to indicate an opening cycle or a specific position of the door. The operators are non-handed and not dependent on the hinges. The operators suit both pushing and pulling arm systems.
The product is delivered complete with back plate, control unit, end plates and cover. Next Page. Page 3: Table Of Contents Sync cable for double doors synchronizing of 2 operators Coordination unit only for Besam SW LED Cable Battery backup unit Double door kit Closing time board kit only for Besam SW Fire kit only for Besam SW Page 4 PULL arm system Issue EI It is to be installed indoors where it is suitable for almost all types of external and internal swing doors.
Disconnect power before removing electronics and battery and make sure it is disposed of properly according to local regulations how and where as was done with the packaging material. Page Technical Specifications 4 Technical specifications Technical specifications Ensure that the door operator with technical specification below is suitable for the installation. Page 11 4 Technical specifications This product is to be installed internally. The push- or pull arm system that is connected to the output shaft opens the door in a surface mounted application.
Before the door is fully open at back check, it slows automatically to low speed. An audible warning signal can be achieved by using the accessory board AIU. The sensor is mounted to the approach side of the door. The operators suit both pushing and pulling arm systems. Page Double Operator, Surface Mounted 6 Models Double operator, surface mounted The product is delivered complete with back plate, control unit, end plates and cover.
Total cover min. Two operators can be mounted under the same cover full length or a modular to open one door each. Page 22 7 Part identification Item No. Page Arm Systems 8 Arm systems Arm systems The installation process of arm systems is the same for Fire door installations, Basic installations and Inverse installations. Pushing installation with PUSH-arm This arm system is delivered with drive arm, telescopic part and door fitting.
It is used if the oper- ator is installed on the wall on the opposite side of the door swing, and approved for fire door ap- plication for A up to mm. Approved for fire door application for A up to mm. It can be fitted on combinations of doors and jambs walls , where the wall thickness does not exceed approx.
See page 51 for installation and adjustment. Page Led Cable Art. No: EI No: Labels Label kit- including all below Art. Activation by disabled people Operator designed for disabled people Page Pre-Installation 10 Pre-installation Pre-installation Page Installation Examples 10 Pre-installation Page Tools Required 10 Pre-installation Page Mechanical Installation 11 Mechanical installation Mechanical installation The operator is mounted on either side of the door header depending on type of doors.
The door is controlled with a push or pull arm system. If a coordination unit is to be installed on a double door installation, mount the coordinator base with rotor before mounting the control unit, see page
0コメント